Founder is the federal State budgetary
Educational Institution Higher Professional
Education "Bryansk State Technical University"
Doctor of Technical Sciences, Professor Fedonin O. N.
Candidate of Technical Sciences, Docent
Candidate of Technical Sciences, Docent
Members of the editorial board
Averchenkov V.I, Doctor of Technical Sciences, Professor (Bryansk)
Buhach A., Doctor of Technical Sciences, Professor (Poland)
Gorlenko O.A, Doctor of Technical Sciences, Professor (Bryansk)
Erohin D.V, Candidate of Economic Sciences, Professor (Bryansk)
Klimenko S.A, Doctor of Technical Sciences, Professor (Ukraine)
Kobischanov V.V, Doctor of Technical Sciences, Professor (Bryansk)
Petreshin D.I, Doctor of Technical Sciences, Professor (Bryansk)
Pruteanu O., Doctor of Technical Sciences, Professor (Romania)
Sitazh M., Doctor of Technical Sciences, Professor (Poland)
Smolentsev V.P, Doctor of Technical Sciences, Professor (Voronezh)
Stepanishev A.F, Doctor of Philosophical Sciences, Professor. (Bryansk)
Suslov A.G, Doctor of Technical Sciences, Professor (Moscow)
Khandozhko A.V, Doctor of Technical Sciences, Professor (Bryansk)
Heifetz M.L, Doctor of Technical Sciences, Professor (Belarus)
by Federal Service for Supervision of Legislation
in Mass Media and the protection of cultural heritage
PI ¹ FS77-21709 August 17, 2005
Address editorial office:
7, Bulvar 50-letiya Oktyabrya,
Bryansk, 241035, Russian Federation
tel. (4832) 58-82-77
e - mail: firstname.lastname@example.org
The subscription index of catalogue
“Russia press” - 18945 semi-annual,
15621 – annual.
It is issued in February 2004.
4 numbers a year
Barabanova I. A. The methodological approach to the content and design of standards on dimensional cutting tool. Questions of standardization of dimensional cutting tools have been considered. A new methodological approach to the content and design standards for the instru-ments was proposed. On the taps example were elaborated projects of new standards establishing the modern science-based regulations and requirements to manufacture and application of di-mensional cutting tools, which can form the basis for standards development for organizations or renewing the existing national standards.
Key words: standardization; dimensional cutting tools; taps, manufacturer standard; purchaser standard.
Sjanov S.J. Algorithm and the software for definition of optimum conditions of electro-physical processing. The algorithm is submitted and the software for definition of conditions of electrophysical processing is described depending on required parameters of quality of a superfi-cial layer at the minimal cost price and the maximal productivity.
Key words: algorithm; the program; productivity; the cost price; electrophysical processing; de-terioration.
Stepanov Y.S., Barsukov G.V., Micheev A.V. Modeling of abrasive grains participating in part surface formation at cutting with hydroabrasive jet. The authors of the paper have elaborated a mathemati-cal model for abrasive grains amount participating in the process of a part surface formation in the course of cutting with a hydroabasive jet that allows the definition of an abrasive essential concentration depending on effluent jet pressure, feed velocity in a jet, dimensions of an abrasive grain and physico-mechanical properties of material.
Key words: abrasive water jet; cutting; abrasive; modeling; destruction.
Rybakov A. V., Okunkova A. A. Solving of work preparation problems of parts, produced by wire electrical discharge macining (by the example of mold parts in pro/engineer system). The existent methods of mold parts surfaces making, properties and differences of mechanical and wire electrical discharge machining (WEDM) were considered in this article. The presentation ways of parts cutting region in the CAM-system and the example of surfacing methods using such as the multi-purpose way during programming of 4-axis wire motion path in WEDM were viewed.
Keywords: work preparation; wire electrical discharge machining; cnc-machines; mold parts.
Bleichmidt L.I., Parfyonov N. S. Estimation of the remaining resource of the tower crane kb-572, residing in oao «dyatikovo-doses». Presented results of the researches on estimation of the remaining resource steel lattice framework of the tower tap KB 572 with use of a program complex.
Key words: remaining resource; steel lattice framework; tower taps.
Fokin Y.I., Yanchenko V.S., Zhuravlev V.V. Peculiarities of the device of fuel elements and prospect of their wide use in a national economy. The theoretical bases of job of fuel elements are given, their detailed classification is considered. The basic advantages of electrochemical generators are analysed, the examples of their use are given.
Key words: Electrochemical generator; fuel cell; electrolyte; electrode; fuel; oxidizer.
Gogolev I.G., Osipov A.V., Birykov A.V. Stream Structure in the interstage clearance at alternating regime of selected department of steam turbine work. The results of an experi-mental of the flow between levels of the model selected compartment steam turbines. We con-sider experimental field distribution along the length blade full and static pressure and flow angles and tangensalnoy and radial planes at several values of air flow in the selection and al-ternating modes before selection stages.
Key words: not axisymmetric flow; selected compartment, heat turbine, the structure of the flow.
Safonov A.L. Using modern methods of calculation of the thermal operating modes of elec-tric connectors. There are techniques for calculation of thermal operating modes of electric connectors. Application of a method of final elements for definition of temperature fields in sec-tion of an electric connector is presented.
Keywords: electric connector; temperature calculation; stationary temperature field; final ele-ments method.
Simkin N.V. Architecture and software graphic systems on the basis of programmed logic the integrated circuit virtex-ii pro. Are developed architecture and software of graphic system in integrated environment(Wednesday) of automation of designing of electronics Xilinx ISE Design Suite.
Key words: architecture; the software; graphic system; designing; PowerPC; the built - in processor.
Afonina E.V., Antipova R.K. Features of creation of volume models of worm pair in the ñompas-3d. Features of performance of volume models of worm gears in system of three-dimensional solid-state modelling of Kompas-3D are considered. The algorithm of creation of 3D-models of a worm and wheels is offered.
Key words: volume model; a worm wheel; cylindrical a worm; a tooth profile; a worm reducer.
Zaikin A. N., Pamfilov E. A., Izjumova E. G. Àutomation of calculation of operational modes of complete sets of machines. The major factors influential in increase of functionability of complete sets of means are parsed. The features of a technique of the automated calculation of modes of operation of complete sets of means are reviewed.
Key words: functionability; technological system; complete set of machines; operational modes.
Shumskiy P.J. The automated system of estimation of a condition of the process equipment, its appointment, advantage and work principle. The problem in the field of an estimation of a condition of the process equipment is stated. Appointment, a principle of work and advantage of use of system are stated.
Key words: system; estimation; condition; suitability; the process equipment.
Bugaev Y.V., Sukhanov P.T., Kolesnik A.V. Identification of the foodstuffs colours accord-ing the results processing by the planar chromotography methods based on colour classifi-cation. Methods of the foodstuffs colors identification according the colors of tinted images based on planar chromatography results are considered in the article. As a math technique a fuzzy set technique is used. Membership functions for a tested set of the colors in the HLS space (Hue, Lightness, Saturation) of the color imaging are formed.
Key words: color image classification; fuzzy sets; planar chromatography.
Roschin K.V. The analysis mechanical pressure in radioelements outputs at ibration effects. Requirements to a method of a time estimation before the fatigue failure of radioelements (RE) outputs are formulated at vibration effects. The hierarchical approach is put in a basis of a method of time estimation before fatigue failure of RE outputs.
Key words: radioelements outputs; fatigue failure; harmonious; casual vibration; fluctuations; pressure; dynamic influences.
Simukov I.V. Comparison of mathematical models of calculation of effective power of pis-tons DVS, rotor-piston engine Vankelya and new rotor combustion engine with two tops at a rotor. The model of mathematical calculation of effective power of new is developed rotor combustion engine with two tops in a rotor. The mathematical models of calculation of power for different engines are confronted (two-stroke DVS, four-stroke DVS, RPD Vankelya, new rotor engine). The analogy of new is exposed rotor engine with four-stroke DVS. Similarly a new engine saved structural advantages of rotor engines.
Key words: mathematical model; effective power; comparison; engine; new construction.
Dubanevich E.V. Perfection of a control system by competitiveness of the industrial enter-prise. Teoretiko-methodical aspects of perfection of competitiveness of the industrial enterprise are considered. In particular, the analysis of existing approaches to definition of the term "com-petitiveness" is carried out, the technique complex an estimation of groups of the factors defining competitiveness of the enterprise, and also the scheme of forecasting of actions for its increase is offered.
Key words: management of competitiveness; forecasting of increase of competitiveness.
Korsakova I.M. Increasing quality to product by way to odernizations of the technological equipment. They are considered actual questions of increasing quality produced to product. It is shown influence to modernizations of the technological equipment on reception required geo-metric factors quality to machine-building product. Work is cited an instance at modernizations of the special lathe.
Key words: operational parameters of the equipment; modernization of the process equipment; quality of let out production; balance of errors; geometrical parameters of quality.
Kholodovskaya A.V. Some of the social and psychological mechanisms of the conformism formation. In this article there are considered the social and psychological mechanisms – passiv-ity, “a social mask”, an inferiority complex in the forming of the conformist personality.
Key words: conformism; passivity; social laziness; a social role and “a social mask”; an inferiority complex.
Kieva O.V. The problem of evaluating students’ works of translation. The work considers the problem of translation teaching methods. Some criteria of evaluating students’ works of translation are offered.
Key words: written translation; activity paradigm; sufficient translation; equivalent translation; translation strategy; criteria of evaluating.
Badolato M., Olson M., Arbogast A. The development of the middlesex community college online learning program. The article by Michael J. Badolato, Ed.D., Dean of Academic Re-sources and Instructional Technologies Division, Matthew W. Olson, Ed.D., Director of Middle-sex Interactive and Sanford A. Arbogast M.Ed., Instructional Technologies Systems Analyst de-scribes creation and development of the online distance learning program at Middlesex Commu-nity College (USA).
Key words: distance learning; online courses; educational services; training methods.